20. Check For Broken Or Binding Servo Cable - Remove servo cable from servo. Check for broken or bin

Ok the cruise control never worked when i bought the vehicle. I have found a test to perform to diagnose tom cruise cocktail movie the cruise control problem....Here's the test...My question will be after the test that i am posting....
1. Check Power To Servo - Unplug harness tom cruise cocktail movie connector from servo. tom cruise cocktail movie Turn ignition on. Using DVOM, measure voltage between pins No. 7 and 10 of servo connector. See Fig. 1 . If battery voltage exists, go to step 4). If battery voltage does not exist, go to next step.
2. Check Power To Servo - Turn ignition on. Check for battery voltage between servo connector pin No. 7 and chassis ground. If battery voltage exists, go to next step. If battery voltage does not exist, check fuses and replace as necessary. If fuses are okay, repair open power circuit. If fuse repeatedly blows check circuit for short to ground and repair as necessary.
3. Check Module Ground - Measure resistance between servo connector pin No. 10 and chassis ground. If resistance is less than 5 ohms, repeat step 1). If resistance is greater than 5 ohms, repair tom cruise cocktail movie ground circuit.
4. Check Deactivator Switch Circuit - Turn ignition on. With brake released, measure voltage between pin No. 9 at servo connector and ground. If battery voltage exists, go to step 7). If battery voltage does not exist, go to next step.
5. Check Power To Deactivator Switch - Disconnect deactivator switch harness connector. Deactivator switch is either a pressure activated switch in the brake hydraulic circuit (on or near master cylinder) or a brake pedal mounted switch in addition to stoplight switch. Check for battery voltage at specified wire. See the BRAKE/DEACTIVATOR SWITCH POWER TABLE . If battery voltage exists, go to next step. If battery voltage does not exist, check for blown fuse or open circuit. Repair as necessary.
6. Check Deactivator Switch-To-Servo Circuit - Measure resistance between servo connector pin No. 9 and matching wire color at deactivator switch harness connector. If resistance is less than 5 ohms, replace deactivator tom cruise cocktail movie switch. If resistance is greater than 5 ohms, repair open circuit between tom cruise cocktail movie deactivator switch and servo connectors.
7. Check Stoplight Switch - With brake pedal released, measure voltage on pin No. 4 at servo connector. If battery voltage exists, replace stoplight switch. If battery voltage does not exist, go to next step.
8. Check Stoplight Circuit - Measure voltage on pin No. 4 at servo connector while depressing brake pedal. If battery voltage exists, go to step 12). If battery voltage does not exist, go to next step.
9. Check Stoplight Switch Resistance - Disconnect stoplight switch. Measure resistance across tom cruise cocktail movie stoplight switch terminals while exercising switch. If resistance is less than 5 ohms with brakes applied, go to next step. If resistance is greater than 5 ohms, with brakes applied, replace stoplight switch.
10. Check Power To Stoplight Switch - Disconnect stoplight switch harness connector. Check for battery voltage at stoplight switch. See BRAKE/DEACTIVATOR SWITCH POWER TABLE . If battery voltage exists, go to next step. If battery voltage does not exist, check for blown fuse or open circuit. tom cruise cocktail movie Repair as necessary.
11. Check Stoplight Switch-To-Servo Circuit - Measure resistance between servo connector pin No 4 and matching color wire at stoplight switch harness connector. If resistance is less than 5 ohms, check harness connectors for corrosion or damage. Repair as necessary. If resistance is greater than 5 ohms, repair open circuit between stoplight switch and servo connectors.
12. Check For Stuck ON Switch - With no cruise control switches pressed, check voltage on pin No. 5 at servo connector. If battery voltage exists, replace cruise control switch assembly. If battery voltage does not exist, go to next step.
13. Check ON Switch Operation - While pressing cruise control ON switch, measure voltage of pin No. 5 at servo connector. If battery voltage exists, go to step 17). If battery voltage does not exist, go to next step.
14. Check For Power To Clockspring - Disable air bag system. Disconnect clockspring connector tom cruise cocktail movie at base of steering tom cruise cocktail movie column. Turn ignition on. Check for battery voltage on specified wire at clockspring harness connector at base of steering column. See CLOCKSPRING POWER CIRCUIT table. If battery voltage exists, go to next step. If battery voltage does not exist, replace blown fuse or repair open circuit between fuse panel and clockspring connector.
15. Check Clockspring - Disable air bag system. Disconnect clockspring connector at base of steering column. Remove drivers-side air bag module. Remove cruise tom cruise cocktail movie control actuator switch assembly. Measure resistance of all wires between base of steering column and actuator switch connector on clockspring. If resistance is greater than 0.5 ohm on any circuit, replace clockspring. If resistance is less than 0.5 ohm on all circuits, go to next step.
16. Check Circuits From Clockspring tom cruise cocktail movie To Servo - Disconnect servo electrical connector. Measure resistance of wire between servo terminals No. 5 and corresponding color wire at clockspring connector at base of steering column. Repeat procedure for servo connector terminal No. 6 circuit. If resistance is greater than one ohm, repair suspect wire(s). If resistance is less than one ohm, check circuits for short to ground. If circuits are okay, go to next step. If circuit(s) are open or shorted to ground, repair as necessary.
17. Check For Stuck Switch - Disconnect servo connector. Measure resistance between terminals tom cruise cocktail movie No. 5 and 6 at servo connector. DO NOT press any cruise tom cruise cocktail movie control switches on steering wheel. If resistance is greater than 3000 ohms, go to next step. If resistance is less than 3000 ohms, replace cruise control command switch assembly.
18. Check Switch Resistance - To check switches, measure tom cruise cocktail movie resistance between tom cruise cocktail movie pins No. 5 and 6 of servo connector while pressing each control button. If any resistance is not as specified, replace control switch assembly. See CONTROL SWITCH RESISTANCES table. If all resistances are as specified, go to next step.
19. Check Vehicle Speed Sensor ( VSS ) Circuit - Test drive vehicle. If speedometer is inoperative, diagnose and repair VSS or VSS circuit as necessary. If speedometer operates properly, disconnect harness connectors from VSS and servo. Measure resistance of wire between servo pin No. 3 and same wire at VSS harness connector (pin No. 3 and anti -lock brake module harness connector on Taurus SHO ). If resistance is less than 5 ohms, go to next step. If resistance is greater than 5 ohms, repair open in VSS (servo pin No. 3) circuit.
20. Check For Broken Or Binding Servo Cable - Remove servo cable from servo. Check for broken or binding cable by pulling on cable ball slug. Replace cable as necessary. If cable is okay, replace servo.
Okay here is what happened....For Step #1 I got 11-12 volts, which is correct. tom cruise cocktail movie It says then to go to Step #4. I got 11-12 volts there, which is also correct. So, I then went to Step #7, like it says. Ok on Step #7, I got 0.3 volts. This is different than the voltage i got for everything else. (All other voltages are supposed to be around the 12 volt battery voltage). It then says If I get voltage, to go ahead and replace the stoplight switch. My question is: Is the 0.3 volts considered to be enough voltage to go by the Step #7, (I am wondering because there's supposed to be either tom cruise cocktail movie one or the other, either no voltage or battery voltage) and replace the switch? Or where, or what step should I go to next, if the stoplight switch is okay? I know that the brake light all work and the recall has been done.
Ok, now moving on I went ahead and went to Step #8 I got the correct voltage there. It then says to go to Step #12. I got no voltage there. It then says to go to Step #13. I got no voltage there. It then says to go to Step # 14. This is where I stopped because of lack of time, and also I have to learn about how to go about doing this step (Step #14). Also, my horn works.
Ok, does anyone here have any ideas as to what else to look for??? Sorry Post is so long, just wanted to be thorough. I will be moving on to next step, but have to wait til monday, when i'm off. Oh, and 1 more thing...I also disconnected the the speed control deactivator switch above the stoplight switch and resetted that.....Thanks for everybody's help. everyone tom cruise cocktail movie has been very helpful!!!
UPDATE: I GOT MY CRUISE tom cruise cocktail movie CONTROL TO WORK!!!! Well after some advice on here about taking the steering wheel switches apart and cleaning them, I found that the switches were shot, no cleaning were gonna fix them. So, I went to Pick-A-Part and picked me up 3 sets of steering wheel cruise control switches( I got 3 pairs just in case) for $7. I then installed them and now was able to do the cruise control self-test diagnostic thing. I was led by the cruise control diagnostic tom cruise cocktail movie test to the cruise deactivator switch on the brake pedal. I took switch off and did ohm test, and it failed. I then, per instruction manual from Alldata (Alldata was a good investment) bypassed the deactivator switch and took the car for a test drive, and sure enough my cruise control worked! SO, I will be buying the switch for $26. And everyone lives happily ever after LOL... Thanks for everyone's help on this site!!!!
AutoGuide.com provides the latest car reviews, auto show coverage, new car prices, and automotive news. The AutoGuide network operates more than 100 automotive forums where our users consult peers for shopping information and advice, and share opinions as a community.